It is important to keep your valve in good condition and replace worn or damaged parts. Hanningfield can supply all spare and wear parts in the Sterivalves range, including technical documentation. Typical parts and spares: - Gaskets/valve seals (translucent silicone, EPDM, FKM (Viton®), PTFE) - Sleeves (PTFE) - Valve actuator replacement (air actuator / stainless steel lever / electric motor) - Actuator parts kit - Replacing dampers and rotors
The heavy duty rotary valve is suitable for pharmaceutical, chemical and food industries. - Delivers large volumes of powder at a controlled rate. - cGMP design - Allows precise dosing of the material. - The Rotovalve Heavy can be supplied with an included control panel allowing the user to adjust and change the rotation speed, set the number of revolutions and, if necessary, operate load cells for high precision applications. - All parts can be easily disassembled for easy cleaning. - All contact parts are made of 316L steel, and non-metal parts are FDA compliant. Full documentation is provided with each valve.
Размеры | DN50, DN100, DN150, DN200, DN250 |
Материалы | нержавеющая сталь EN 1.4404 (AISI 316L) |
Финишная обработка | Ra 0.5 мкм внутри |
Characteristics
- Stops powder flow allowing unloading when needed. Ideal for use on IBCs and containers. - cGMP design - Easy to install - top and bottom halves connections can be supplied to match customer's existing ones. - All parts can be easily disassembled for easy cleaning and replacement of wear parts. - All contact parts are made of 316L steel, and non-metal parts are FDA compliant. Full documentation is provided with each valve. - Can be supplied with a drive to automate the unloading if the manual lever is not suitable. - The valve can be equipped with various accessories to improve its performance, such as a positioner, when the customer wants to control the angle of the damper,
Размеры | DN80, DN100, DN150, DN200, DN250 |
Материалы | корпус - нержавеющая сталь EN 1.4404 (AISI 316L) |
Финишная обработка | Ra 0.5 мкм внутри |
Characteristics
The Rotocrusher is a clod crusher (rotary crushing valve) with a minimum throughput of 750 kg/h and a maximum of 3000 kg/h.
Размеры | DN100, DN150, DN200, DN250 |
Материалы | нержавеющая сталь EN 1.4404 (AISI 316L) |
Финишная обработка | Ra 0.5 мкм внутри |
Characteristics
Split butterfly valves consist of two parts: an active half and a passive half. Typically, the active half is connected to a receiving vessel or processing machine, while the passive half is usually mounted on a discharge drum or similar device.
Размеры | DN50, DN100, DN150, DN200, DN250 |
Материалы | корпус и бабочка – нержавеющая сталь EN 1.4404 (AISI 316L) |
Финишная обработка | Ra 0.5 мкм внутри |
Characteristics
The lightweight rotary valve is suitable for the pharmaceutical, chemical and food industries. - Delivers large volumes of powder at a controlled rate. - cGMP design - Easy to install - top and bottom halves connections can be supplied to match customer's existing ones. The valve is powered by a pneumatic actuator requiring a connection to compressed air, which means no wiring and simplifies valve testing in ATEX areas. - All parts are easily disassembled for easy cleaning and replacement of wear parts. - All contact parts are made of 316L steel, and non-metal parts are FDA compliant. Full documentation is provided with each valve. - Can be supplied with a small gap between rotor and gasket to prevent gasket friction with each revolution.
Размеры | DN80, DN100, DN150, DN200, DN250, DN300, DN350, DN400 |
Материалы | корпус и ротор нержавеющая сталь EN 1.4404 (AISI 316L) |
Финишная обработка | Ra 0.5 мкм внутри |
Characteristics
The Rotodoser is designed for applications where high precision and accurate dosing are required. - Provides the user with high-precision dosing and full control over the supply of material. - cGMP design - Easy to install - top and bottom halves connections can be supplied to match customer's existing ones. - All parts are easily disassembled for easy cleaning and replacement of wear parts. - All contact parts are made of 316L steel, and non-metal parts are FDA compliant. Full documentation is provided with each valve.
Размеры | DN100, DN150, DN200, DN250 |
Материалы | корпус – нержавеющая сталь EN 1.4404 (AISI 316L) |
Финишная обработка | Ra 0.5 мкм внутри |
Characteristics
The Rotovalve Plus is designed to assist in the loading and volumetric dosing of bulk solids. - Delivers large volumes of powder at a controlled rate. - Ideal for applications where a higher degree of accuracy is required (compared to Rotovalve Light). - CIP and SIP cleaning - All parts are easily disassembled for easy cleaning and replacement of wear parts. - All contact parts are made of 316L steel, and non-metal parts are FDA compliant. Full documentation is provided with each valve. - cGMP design - Easy to install - top and bottom halves connections can be supplied to match customer's existing ones.
Размеры | DN100, DN150, DN200 |
Материалы | корпус и ротор – нержавеющая сталь EN 1.4404 (AISI 316L) |
Финишная обработка | Ra 0.5 мкм внутри |
Characteristics
We understand that standard valves are not always suitable for your application and therefore we offer customized solutions for our customers. Most often, modified top and bottom halves connections are required if the standard connection types do not match the connection types on existing equipment.
- Stops powder flow allowing unloading when needed. Ideal for use on IBCs and containers. - cGMP design - Easy to install - top and bottom halves connections can be supplied to match customer's existing ones. - All parts can be easily disassembled for easy cleaning and replacement of wear parts. - All contact parts are made of 316L steel, and non-metal parts are FDA compliant. Full documentation is provided with each valve. - Can be supplied with a drive to automate the unloading if the manual lever is not suitable. - The valve can be equipped with various accessories to improve its performance, such as a positioner, when the customer wants to control the angle of the damper,
Размеры | DN80, DN100, DN150, DN200, DN250, DN300, DN350, DN400 |
Материалы | корпус и бабочка – нержавеющая сталь EN 1.4404 (AISI 316L) |
Финишная обработка | Ra 0.5 мкм внутри |
Characteristics